AKG IVM4500 Specifications download pdf (Page 31)

3 Setting Up

Setting Up the

Receiver

nserting Batteries

Refer to fig. 9.

ote:

Important!

Powering Up

(LOCK/SETUP Modes)

LOCK Mode:

SETUP Mode:

Selecting Modes:

Powering Down

Automatic

Frequency Selection

1. Open the battery compartment (1).

. Insert the two supplied batteries (2) into the battery compartment, aligning the

batteries with the polarity symbols inside the battery compartment.

f you insert the batteries the wrong way, the receiver will not be powered.

3. Close the battery compartment (1).

•

Alternatively to the supplied dry batteries, you may use the optional BP 4000

battery pack from AKG. The BP 4000 fits into the battery compartment in the

orrect orientation only, so you cannot insert it the wrong way.

•

Please note that standard rechargeable batteries may damage the receiver

if the charging contacts are shorted and will provide no meaningful remain-

ing-battery-life indication. AKG will accept no liability for any damage re-

ulting from the use of standard rechargeable batteries.

• Set the rotary control to position 1 or higher.

- Status LED is lit green: power to receiver is on, radio link operating.

- Status LED is lit red: power to receiver is off or batteries will be dead in less

than 60 minutes.

- Status LED remains dark: no batteries or dead batteries inside battery com-

partment.

• When powering up for the first time, the first thing you need to do is select a Pre-

set. Read on in section "Automatic Frequency Selection.

• When powering up again later, the receiver will automatically come on in LOCK

mode. The display will indicate the selected frequency in MHz for about 2 sec-

onds, the battery type ("BATBAT" – two dry batteries, "-Accu-" – BP 4000) for

about 2 seconds, and finally the frequency as a Preset Subchannel.

The receiver is electronically locked so you cannot make any adjustments. The

"LOCK" label is lit on the display.

• You can scroll through the following status screens:

- Preset (comes up only if a Preset has been saved): Carrier frequency shown

as a Subchannel number within a Frequency Group.

- Frequency: Carrier frequency in MHz. (This screen is always available, even

if no Preset has been saved.)

- Battery: Percent battery capacity. (This screen is only available if you are

using a BP 4000 battery pack.)

In SETUP mode, the electronic lock is disabled so you can adjust all receiver pa-

rameters. The "LOCK" label is not shown.

• To toggle between LOCK and SETUP modes, hold down the Jog switch for

about 2 seconds.

• Set the rotary control to the "OFF" position.

1. Switch all transmitters OFF.

2. Select the "AUTO" menu to start the automatic frequency search.

The currently active frequency GROUP starts flashing. The receiver scans all

preset frequencies (CHANNELs) within the selected GROUP.

The "FREE" field lists the number of clean channels.

3. If the receiver has found enough CHANNELs for your system, confirm the se-

lected GROUP.

If the clean CHANNELs found are fewer than required, use the jog switch to se-

lect a different GROUP.

4. Having selected and confirmed a GROUP, you can use the jog switch to select

any clean CHANNEL within this GROUP.

5. Select the CHANNEL to which you wish to program your system.

6. Program the transmitter to the same GROUP and CHANNEL referring to the

section on "Selecting Frequencies from the Preset Screen".

IVM

4500

BDA_IVM4500_120311_Kern_final:Layout 1 05.06.2012 12:28 Uhr Seite 31

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 124 125

Comments to this Manuals

No comments

AKG IVM4500 Specifications Page 31

Comments to this Manuals

Related products and manuals for Routers AKG IVM4500